A sanding block

A sanding block is a block used to hold sandpaper. In its simplest form, it is a block of wood or cork with one smooth flat side. The user wraps the sandpaper around the block, and holds it in place. Fancier versions use clips, teeth or clamps to hold the paper in place. Commercial versions can be constructed of various materials. They are usually sized to hold a quarter or half sheet of sandpaper. Some versions use the sandpaper belts intended for a power belt sander. Sanding blocks are helpful because they prevent the "waves" created by plain sandpaper.

Know at least two safety procedures for each of the above tools: The main safety rule to follow with any tool is to use common sense.

Coping saw 1. Clamp your work firmly to a bench before cutting it with a coping saw. You may wish to pad the clamp with a piece of scrap wood so it does not mar the piece. 2. Be careful not to saw into the bench. 3. Keep your fingers clear of the blade. Rasp 1. Do not draw the rasp across your skin - it will cut skin even easier than it will cut wood. 2. Do not strike a rasp with a hammer or mallet or it may shatter. Plane 1. Do not test the sharpness of a plane's blade by sliding it along a finger. 2. Retract the plane blade when storing. 3. Keep the blade sharp. Knife 1. Do not push the knife toward another person (or yourself!) when cutting. Imagine the path blade will follow if the item you are cutting suddenly give way, freeing the blade. Always make sure nothing is in that path. 2. If you drop a knife, let it fall. Do not try to catch it. 3. When handing a knife to another person, offer them the handle - not the blade. 4. Do not throw the knife. 5. Do not use a locking knife unless the blade is locked. 6. For non-locking knives that fold, be aware that it may close on your hand if you apply pressure the wrong way. 7. Do not pry with a knife - you may break the blade. 8. Keep the blade sharp. Chisel 1. Store the chisel with the blade covered. 2. Keep the blade sharp. 3. Keep both hands behind the blade. 4. Use a mallet with the chisel rather than pushing it along with your hand. This will ensure that your hands are both behind the blade. 5. Do not put a chisel in your pocket. Sanding block 1. Do not throw a sanding block 2. Pay attention to the path of the sanding block. It is easy to knock something over when you're paying attention to the piece you're sanding instead of the surrounding environment. 3. Do not sand skin. Sand papers will abraid skin.

[edit] List of handicraft trades

Handicrafts include:

• assemblage – collage in three dimensions
• beadwork
• bone carving buffalo, camel, elephant bone carving.
• horn carving buffalo, rhino horn carving.
• cabinet making
• chip carving
• collage possibly involving seeds, fabric, paper, photographs and/or found objects
• crochet
• embossed aluminum or silver
• gardening
• knitting
• Lathart
• marquetry
• metalwork
• scale model
• mosaic
• needlework
• pottery and ceramics
• pressed flower craft — uses real flowers and leaves
• puppetry
• quilting - also reference Quilt and Art quilts
• sewing
• shoemaking
• spinning
• stained glass
• wood burning
• wood carving
• woodturning
• woodworking
• List of handicraft manufacturers

chise

A chisel is best used with a mallet. Chisels can be used for removing great quantities of wood. They can cut across the grain or slice along its length. Chisels are sharpened much the same way as knives, but the angle is a bit steeper, ranging from 20° to 35°. Often they are sharpened at two angles, such as 25° for most of the length of the blade, and 35° near the edge. This allows the blade to be resharpened by only honing a small portion near the cutting edge.

[edit]

The primary tool for wood carvin

Carving knives, chisels, and gougesg is a carving knife. You can use a pocket knife as well, and many people do. To sharpen a knife, hold the blade at about a 15° angle and scrape it along a whetstone as if you were trying to shave off a thin layer of the stone. Be sure to sharpen both sides

Plane

A hand plane is a tool for shaping wood. Planes are used to flatten, reduce the thickness of, and impart a smooth surface to a rough piece of lumber. Hand Planes are one of the most satisfying tools to operate. Clamp the wood securely to a bench, and then push the plane along the grain. The blade should be adjusted so that it takes a thin shaving off the plank. A sharp, well adjusted plane will remove a continuous shaving the entire length of the board. Pay attention to how the grain runs - if the grain dives into the board, make sure the plane's blade does not break the shaving off below the surface. If this happens, try planing in the other direction (see illustration). Once the blade has been removed from a plane, it can be sharpened in the same fashion as a chisel. It should be sharpened frequently, as this will greatly improve its performance. A plane should be stored on its side to respect the blade. You should also be very careful to not plane into a nail or a screw, as doing so will put a nasty notch in the blade.

Rasp

A rasp is a woodworking tool used for shaping wood. It consists of a point or the tip, then a long steel bar or the belly, then the heel or bottom, then the tang. The tang is joined to a handle, usually made of plastic or wood. The bar has had sharp teeth cut into it. Rasps generally cut more coarsely than files. They are useful for rapidly removing wood from curved surfaces. They remove less wood than a drawknife, so they are easier to control. Even though rasps leave very coarse finishes, the cut-away areas can be easily smoothed with finer tools, such as files. There are several types and shapes of rasps. There is a half round, round and flat. The several types of rasps are bastard, cabinet and wood (finest to coarsest). All these varieties can be used to make different shapes. A similar tool to a rasp is a surform file; it has coarse, individual teeth like a rasp for cutting wood. The difference being that the surform has a small hole near each of the teeth to allow shavings to pass through and prevent clogging. Surform tools come in different styles and shapes including file-plane, round file and shaping/shaving tools.

Coping saw

Coping saws are very useful for removing bulk. A carving can often be roughed in with a coping saw, and once the shape is cut out, knives, chisels, and gouges can be used to clean it up and do the final shaping. Coping saw blades can be sharpened with a triangle file, though they are cheap enough that they ore more frequently replaced when dull. The blade can be installed on the coping saw so that it cuts on either the pull stroke or the push stroke. Experiment to see which you like better. To make a cut, clamp the piece to a bench or hold it firmly with your free hand or knee. Align the blade with the pencil mark you have made which will guide the cut. Gently work the saw up and down to make the cut. You may have difficulty at first, and this does take a little practice to master. But once you have it down, it is not all that difficult. Follow the line until the cut is complete.

Handicraft

Handicraft, also known as craftwork or simply craft, is a type of work where useful and decorative devices are made completely by hand or using only simple tools. Usually the term is applied to traditional means of making goods. The individual artisanship of the items is a paramount criterion, such items often have cultural and/or religious significance. Items made by mass production or machines are not handicrafts.

Usually, what distinguishes the term handicraft from the frequently used category arts and crafts is a matter of intent: handicraft items are intended to be used, worn, etc, having a purpose beyond simple decoration. Handicrafts are generally considered more traditional work, created as a necessary part of daily life, while arts and crafts implies more of a hobby pursuit and a demonstration/perfection of a creative technique. In practical terms, the categories have a great deal of overlap.